Full Project – REPORT ON THE FABRICATION OF SIEVE SYSTEM

Click here to Get this Complete Project Chapter 1-5

ABSTRACT

The construction of sieves system was carried out in the Engineering workshop, Institute of management and technology, Enugu.

The aim of this project is to fabricate a sieve system, which is capable of separating solid particles of various sizes.

The construction was carried out in order to analyze the sizes of particles.

The component parts of the sets of sieve and their dimension are as follow:

Height of sieve –80mm

Number of sieve –4

Diameter of sieve –230mm

Shape of sieve –cirular

Height of sieve set –760mm

Mesh/hole sizes – top –6.0mm, 2nd 5.0mm, 3rd 3.0mm bottom 1.0mm downwards respectively.

In constructing of this sieve system, some factors were taken into consideration and they are:

-the capacity of the sieve

-the type of mixture that can be filtered in it

-the types of properties and decomposition of the mixture.

-the type of material to be used for constructing the sieve.

The cost which is the determinant, factor in fabrication of any equipment.

These factors, help greatly in the fulfillment of the objective of this project study.

At the end of the fabrication, a sieve equipment was construct with specified dimension.

TABLE OF CONTENT

CHAPTER ONE

1.0              INTRODUCTION

CHAPTER TWO

LITERATURE REVIEW

2.1              HISTORY OF SIEVE

2.2              THEORY OF SIEVE

2.3              SCREENING

2.4              STANDARD SCREEN

2.5              MATERIAL BALANCES OVER SCREEN

2.6              EFFECTIVENESS/EFFICIENCY

2.7              SCREEN ANALYSIS

2.8              TYPES OF SCREENING

2.9              EFFECT OF MESH SIZE ON CAPACITY OF SCREEN17

CHAPTER THREE

3.1              MATERIALS OF CONSTRUCTION

3.2              ANALYSIS OF MATERIAL OF CONSTRUCTION

3.3              MAINTENANCE OF SIEVE COMPONENT

3.4              SAFETY PRECAUTION

CHAPTER FOUR

4.1              FABRICATION PROCEDURE

4.2              LAYOUT

4.3              FABRICATION OF SIEVE PLATE

4.4              SMOOTHENING AND FILLING

CHAPTER FIVE

DISCUSSION

CHAPTER SIX

CONCLUSION AND RECOMMENDATION

REFERENCE

APPENDIX

CHAPTER ONE

INTRODUCTION

Generally, all chemical engineering mostly deals with the construction of sieve among others construction in order to fulfill the theory of separations technique. This construction is carried out so as to achieve and put to practice chemical process with the help of some component for equipment construction procedures.

Sieving equipments produces a nice separation of solid particles, although artificially, by allowing the social particles to pass through the pores or the a pasture, which consists of orderly, arrange set of sieves which is arranged in manner with their facilities sizes and shapes.

Sieving equipments operates satisfactory with reasonable coarse and fine particles, so that separation can be done they have high sensitive efficiency, but few have been built since the development of separation of particles, because of the lost and the procedures involved and the labour needed to clean the sieve plate and to handle the sieve equipment.

Moreover, in the construction of set of sieve, we have to bear certain qualities in mind to portray such as determination of size and shape of the equipment which contributes to the efficiency of the equipment.

However, the operation has evolved as a particle at rather than a theoretical science, nevertheless, its theory has received steady attention since the pioneering work of some important scientist half a century ago.

They are usually used in large industries like mining, coal, gold, diamond and pharmaceutical etc, because of its importance and efficiency and would not be seen commonly.

Above all, the purpose of this project is to fabricate a set of sieve which sole aim is for separation of solid particles of different size by passing through the mesh with the help of shaking and larger particles retained on the mesh (oversized) and the particles that passes through (undersized) enables us to separate the particles.

Get the Complete Project

This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for International clients.

Click here to Get this Complete Project Chapter 1-5

You can also check other Research Project here:

1. Accounting Research Project
2. Adult Education
3. Agricultural Science
4. Banking & Finance
5. Biblical Theology & CRS
6. Biblical Theology and CRS
7. Biology Education
8. Business Administration
9. Computer Engineering Project
10. Computer Science 2
11. Criminology Research Project
12. Early Childhood Education
13. Economic Education
14. Education Research Project
15. Educational Administration and Planning Research Project
16. English
17. English Education
18. Entrepreneurship
19. Environmental Sciences Research Project
20. Guidance and Counselling Research Project
21. History Education
22. Human Kinetics and Health Education
23. Management
24. Maritime and Transportation
25. Marketing
26. Marketing Research Project 2
27. Mass Communication
28. Mathematics Education
29. Medical Biochemistry Project
30. Organizational Behaviour

32    Other Projects pdf doc

33. Political Science
34. Psychology
35. Public Administration
36. Public Health Research Project
37. More Research Project
38. Transportation Management
39. Nursing

Education

Full Project – REPORT ON THE FABRICATION OF SIEVE SYSTEM