Full Project – CONSTRUCTION OF HEAT EXCHANGER FABRICATION OF A TUBE AND SHELL HEAT EXCHANGER SYSTEM

Click here to Get this Complete Project Chapter 1-5

ABSTRACT

            There are two methods of constructing heat exchangers: Plate type.  Parallel flow-the hot fluid and the coolant flow in the same direction.

Counter flow:-           The hot fluid and the coolant flow in opposite direction.  Cross flow: The hot fluid and the coolant flow at 90 angles (perpendicular) to each other.

The four heat exchanger parts identified were.  Tube sheet shell Baffles single- pass heat exchangers have fluids that pass each other only once.

Multipass that exchangers have fluids that pass each other more than once through the use of a tubes and baffles.

Regenerative heat exchangers use the same fluid for heating and cooling.  Non-regenerative heat exchangers use separate fluids for heating and cooling process.

TABLE OF CONTENTS

CHAPTERS

1.            INTRODUCTION

2.            LITERATURE SURVEY

3.            FABRICATION PROCEDURE

4.            DISCUSSION

5.            CONCLUSION

6.             COSTING

7.            RECOMMENDATION

8.                  REFERENCES

CHAPTER ONE

            INTRODUCTION

Heat exchanger is a device whose primary purpose is the transfer of energy between fluids.  (J.R. Welty and R.E Witson Fundamentals of momentary heat and mass transfer 2nd edition 1975).

There are many types of heat exchangers, namely shell-and-tube exchanger, tubular and plate exchangers, the spiral plate heat exchanger etc.

In industrial processes, heat energy is transferred by a variety of methods which includes conduction as in electric resistance, waters, conduction as in exchangers, boilers and condensers, radiation as in furnace, radiant heat dryers and by special method such as electric heating.

The heat exchanger is a very important unit or system in small scale industries and also in process industries that their design has been highly developed.  Designers of heat exchanger must be constantly aware of the difference between the idealized condition for and the real conditions of the mechanical expressions of their design and its environment.  The result must satisfy process operational requirements (such as availability flexibility and maintainability) and do so economically.  The most common material for heat exchanger is carbon steel.

Using the simple shell and tube heat exchanger in explain the process.  Hot liquid flows through the tube and cold and more viscous liquid flows through the shell.  The two liquids are collected and cooled by the forced convective air which is supplied by the fan.  The shell side and tube side heat transfer coefficient are of comparable important and both must be large if a satisfactory overall coefficient is to be attained.  The velocity and turbulence of the shell side liquids are as important as those of the tube side flow.

The purpose of this project is to constraint an efficient heat exchangers system which on reasonable basic will help in carrying out heat transfer operation in our laborating and in small scale industries.  Cost of materials and labour is well as time were considered.

Get the Complete Project

This is a premium project material and the complete research project plus questionnaires and references can be gotten at an affordable rate of N3,000 for Nigerian clients and $8 for International clients.

Click here to Get this Complete Project Chapter 1-5

You can also check other Research Project here:

1. Accounting Research Project
2. Adult Education
3. Agricultural Science
4. Banking & Finance
5. Biblical Theology & CRS
6. Biblical Theology and CRS
7. Biology Education
8. Business Administration
9. Computer Engineering Project
10. Computer Science 2
11. Criminology Research Project
12. Early Childhood Education
13. Economic Education
14. Education Research Project
15. Educational Administration and Planning Research Project
16. English
17. English Education
18. Entrepreneurship
19. Environmental Sciences Research Project
20. Guidance and Counselling Research Project
21. History Education
22. Human Kinetics and Health Education
23. Management
24. Maritime and Transportation
25. Marketing
26. Marketing Research Project 2
27. Mass Communication
28. Mathematics Education
29. Medical Biochemistry Project
30. Organizational Behaviour

32    Other Projects pdf doc

33. Political Science
34. Psychology
35. Public Administration
36. Public Health Research Project
37. More Research Project
38. Transportation Management
39. Nursing

Education

Full Project – CONSTRUCTION OF HEAT EXCHANGER FABRICATION OF A TUBE AND SHELL HEAT EXCHANGER SYSTEM